Видео

Hi back 3 years you installed airlift airbags on your motorhome. How much did you gain with full inflation of airbags please reply ASAP thank you PS enjoy your videos.

no do not ask him as ev promotor a great battery for his ev wheel chair the batery will hold him up so he is not faling from it with high speed corners plenty to pul his chevy

i think that will be close to 140 kg ask joe bidden to lift it! for exersise.

Does it have Victron communication compatibility?

nice

What is "ruuf"?

Tito, what size rivets did you use?

Seems the 2/0 cable should be cooler than the 1/0 cable...

I assume you live in a colder area since there is snow. Did you find your floor popped up with the LVP? We live in Canada and I have read that you should not use LVP because it will buckle with heat and cold expansion.

I burst out laughing when you used the side of the hammer lol

Thanks so much

Thank you for the review, I run a48v /100ahr sok battery in my Rv . So far it has been working well

Do you still have to original fitting for the Dometic 9100 that you took off? I need one, mine broke!

what about EternaBond doublestick between RV vent roof square on roof how remove?

I am interested to see how it holds up to travel, especially on rough (Alcan or Dalton) roads. Good video, thank you.

Thanks for the video.

Great video, Tito, as always. The battery is too large for my RV. There is no room in both battery compartments for one large battery. I am still using a flooded battery, and this one is way too big.

There is a reset button on the front. Also for the final load for Max current, your dial up heat gun would have been great. If I remember correctly, the last item fired up was the microwave which has a large current draw all at once. Thanks for the video.

Nice video. There’s too much information out there for me. The more videos I watch the less I know what I want to do with my motor home. I guess I’ll run the diesel generator for now. 😂😂

OCP = Over Current Protection

This is a re-upload you posted this content years ago

Hi Tito I am hoping for your technical assistance. Bought the XP3.0 two weeks ago. While adjusting the break/caliper gap due to existing squeak upon receipt I've noticed oil like substance dripping from the assembly. I'm assuming it's the hydraulic fluid(mineral oil)😔and now i have no breaking action at all when I squeeze the handle. HELP

These BMS's have temp info, but instead of getting complicated by tying into the RS485, you can get an inkbird 308 (w or wo wifi) and have it tell you if your temps adjacent to the battery are getting out of line. Iirc these do not have an internal heater. If you stick a battery directly on your floor, first jam the inkbird probe underneath it, so during the winter you'll get an alert if it gets too cold. These will shut-off the loads and charging at freezing.

How long are the terminal bolts? The EG4's came with bolts that were too short, so by the time you got more than the provided interlink cable connected, you didn't have enough thread engagement to properly torque them with any additional connections. Swapping them out with longer ones, body bolts from a toyota, worked 😂. Make sure you size your terminal bolts, and the depth of the inner threads, and have on-hand longer ones to accomodate all your connections.

Orient Power is not to be trusted.

Those are good. As are SOK, EG4, Trophy... I have 2x 5kw EG4's just stacked on the floor under the seat. For all you mobile platform people, you need 200ah (of) cells of LFPO (@48v) aka 10kw of batteries, to properly run the smallest AOI 3k, appropriate for a mobile platform, like the EG4-AIO 3k, GROWATT 3k, etc.

Exceptional video, you are very articulate and able to explain the water heater troubleshooting process so well. I bought a used RV, installed a new water pump then discovered the water heater wouldn't turn on. I read the owners manual, then the Atwoods manual and neither offered a troubleshooting guide. After watching your video I tested the thermal fuse, it was functional so I reinstalled it and the water heater turned on. I'm going to get extra thermal fuses. plus a spare thermostat and fuse. Thank you! P.S. I hope you have a video on troubleshooting the generator..... The next project, after I replace an exhaust fan and clean the AC coils.

they are now achieving this within the battery itself, so no need to buy multiple batteries.

This is a really neat idea, and correct me if I'm wrong but wouldn't blocking the reflective serface with fabric reduce its effectiveness?

Genius idea! I am just an hour away from installing my flexible solar panel, but now I have to run to the hardware store. Thanks for saving me from making the mistake of gluing my panel directly to the roof!

I like this solution. Did you ever have any problems with it? Thanks great video!

I live in the federal way area, do you recommend Kimball’s. I didn’t hear you price their work or anything. I understand it was 12 years ago. Great videos

Heavy.

Excellent video, however, on mine it works all the way through the propane firing up and lighting, and propane runs about the normal time it would to heat my tank then shuts off, but I still get NO hot water. I am totally baffled by what could be happening here. I believe I have all of the winterization valves turned correctly too! When I sanitized my system prior to using it I of course let my water heater tank fill as part of this and then drained it again as recommended. Only thing I messed with is removing the PRV to allow me to pour vinegar into the tank from the top to let it sit overnight and descale my tank for calcium deposits. But the tank is not dripping anywhere to indicate a pressure leak.

How well did this hold up long term?

I used mine to mold a water bottle around the output of my palm sander and the end of my shop vac 🤷🏻‍♂️

hey what's the top speed?

Twenty years ago I started roasting 400g batches of coffee using the “HGDB” (heat gun dog bowl) method, and am still roasting coffee (2.5kg batches) here in NZ(using a larger hot air roaster). Now I have more uses for the HG!

Nice idea 💡

i had one of those inverters. it did work great for 6 months. if looking for something to last. switch brands

Thanks for this video. I did the same exact thing and it works perfect. No more worry about turning the converter on or off!

First of all, the thanks for the video on replacing the awning motor. Followed all the instructions, including the rush to do wiring and didn’t notice the coupler still sitting on the table. LOL. The jacks on our 2019 NEWMAR Baystar died. The contractor was toast but easily replaced and solved the problem. Contractors are most often confused with relays. Great video.

👍

I didn't need a basic e-bike tutorial, just a review, so this video was way too long. This class foldable e-bike has lots of compromises, it's not a good all rounder bike. Tito didn't need to bother about the class 3 mod or whine about his pedals were going too fast at 28 mph. The Ride1Up Portola is another take on this e-bike. Foldable, higher capacity battery, more fork travel, 180mm hydraulic brakes, and looks better, but not as nice a display. Meh, they're all made in China.

should have shown us how to take the selenoide and the electronic box out step by step.

You made it look good job,,,i would fine me some old car tags and add me some mmore shielding at one place.if its gas it will get hot!!!

It is a bug with these machines that they can run then shut off after 20 mins for no reason IF the oil level is at full. There are several videos on this here on YT. Trick is to only fill 1/4 above ADD mark on dipstick. I had this issue, drained out some oil from full down to 1/4 above add and generator ran for hours as intended. Dont trust me? Search for yourself.

How did you get the awning out some to work on it? My buddies is stuck closed, and all that happens when you click the button, i can hear the motor trying to move but nothing happens.

Thanks. That was very helpful.

Semi flexible converted to a framed rigid panel. Got it.